• <em id="gxpaq"></em>
    <button id="gxpaq"></button>
    1. <th id="gxpaq"></th>
      <rp id="gxpaq"></rp>
    2. <rp id="gxpaq"><samp id="gxpaq"><blockquote id="gxpaq"></blockquote></samp></rp>
    3. <label id="gxpaq"></label>
    4. WELDGRP screenshot
      SOFTWARE :WELDGRP
      DEVELOPER :Alex Tomanovich
      VERSION :2.3
      PLATFORM :Spreadsheet
      FILE SIZE :0.37 MB
      LICENSE :Freeware
      DOWNLOADS :UserDownloads:3657
      WELDGRP Description

      WELDGRP is a spreadsheet program written in MS-Excel for the purpose of analysis of weld groups using either the ultimate strength method (also known as "instantaneous center of rotation" method) or the "elastic" (vector) method ("Alternate Method 1" in AISC Manual). A separate worksheet contains data tables for welds.

      Program Assumptions and Limitations:

      1. The AISC eccentric loads on weld groups worksheets (Tables XX through XXVI, pages 4-75 through 4-82) are applicable for only in-plane shear loads and torques (moments) on the weld group. With the one exception being the "Special Case" of out-of-plane loading for vertical parallel welds, AISC Table XIX.

      2. The "Weld Group (elastic)" worksheet can be used for all cases of in-plane and out-of-plane loads on the weld group, or where geometry limitations of the AISC Tables XIX through XXVI are ecceeded. The "elastic" method (AISC "Alternate" Method 1) will always give conservative results when compared to using the AISC Tables.

      3. The "Weld Group (elastic)" worksheet assumes a minimum of 1 weld and a maximum of 24 welds in a group.

      4. In the "Weld Group (elastic)" worksheet, the welds are treated as "lines" possessing a length, but no actual theoretical thickness. All welds are assumed to contribute to the moment of inertia of the group, and the applied loads are linearly distributed among the welds based on the location of the welds from the centroidal axes.

      5. In the "Weld Group (elastic)" worksheet, the weld group must be composed of straight lines/segments, but they all need not be connected. Circular or portions of a circular pattern weld may be adequately modeled by using a series of segments.

      6. In the "Weld Group (elastic)" worksheet, each weld line/segment is defined by its own start (X1, Y1) and end (X2, Y2) sets of coordinates. Coordinates defining weld lines/segments can be input irrespective of direction. That is, a weld line/segment may be defined from left-to-right and top-to-bottom or vice-versa.

      7. The "Weld Group (elastic)" worksheet assumes an orthogonal X-Y-Z coordinate system. All welds and loads points MUST BE located in the "positive" (1st) quadrant. "Negative" weld or load point location coordinates are NOT permitted. "Right-Hand-Rule" sign convention is used for all applied forces and moments at load point locations.

      8. In the "Weld Group (elastic)" worksheet, the welds and load points can be numbered in any desired order. However, the user should make sure to either clear the contents of all spreadsheet cells that are not used for input or those cell values should be input = 0. All welds and load points MUST BE input in proper numerical sequence with no "breaks" in the numerical order of input data.

      9. The "Weld Group (elastic)" worksheet calculates the required weld size in terms of both fillet leg and effective throat dimensions, based on the assumption of using E70XX welding electrodes. The user should check AISC specification for limitations on minimum and maximum weld sizes.

      * WELDGRP download link provides freeware version of the software.

      Similar Software
      BASEPLT9 Version:3.7 · Alex Tomanovich
      BASEPLT9

      Steel Column Base Plate Analysis per AISC 9th Ed

      BASEPLT9 is a spreadsheet program written in MS-Excel for the purpose of analysis of steel column base plates.

      BMREINF9 Version:2.0 · Alex Tomanovich
      BMREINF9

      Analysis Of Beam Reinforcement per Aisc 9th Edition ASD Manual

      BMREINF9 is a spreadsheet program written in MS-Excel for the purpose of analysis and code checking of steel members with various types of reinforcement configurations.

      BEAMCOL9 Version:3.5 · Alex Tomanovich
      BEAMCOL9

      Beam-Column Design per Aisc 9th Edition ASD Manual

      Beam-Column design, focusing on flexural & axial stresses, including built-up sections not classified as plate girders (per AISC 9th Edition ASD Manual)

      PILEGRP Version:3.6 · Alex Tomanovich
      PILEGRP

      Pile Group Analysis for a Rigid Pile Cap/Mat

      PILEGRP is a spreadsheet program written in MS-Excel for the purpose of analysis of pile groups with rigid caps using the elastic method.

      WeldGroup Version:2016.11 · Yakov Polyakov
      WeldGroup

      Eccentrically Loaded Weld Group Shear Capacity

      Implements AISC LRFD method to calculate capacity of weld group under combined action of eccentrically applied in-plane and normal forces.

      POLEFDN Version:2.3 · Alex Tomanovich
      POLEFDN

      Pole Foundation Analysis

      POLEFDN is a spreadsheet program written in MS-Excel for the purpose of analysis of a pole foundation assuming the use of a rigid round pier which is assumed free at the top and subjected to lateral and vertical loads.

      Comments & Reviews About WELDGRP

      No comments yet. Be the first to comment.

      Submit a review using your Facebook ID

      Rate This Software

      WELDGRP has been rated 5.0 out of 5 points. A total of 2 votes cast and 0 users reviewed the software.

      Most Popular Structural Analysis Downloads

      28340 hitsLTBeam 1.0.11

      LTBeam is a software which deals with the elastic Lateral Torsional Buckling of Beams under bending action about their major axis.

      13164 hitsEBPlate 2.01

      EBPlate is a piece of software developed by CTICM with a partial funding of the European Research Fund for Coal and Steel (RFCS). It assesses the critical stresses associated to the elastic buckling of plates loaded in their plan.

      11804 hitsFTOOL 4.0

      Ftool provides a simple analysis program that merges, in the same interface, resources for effective creation and manipulation of the model, linked to a fast and effective code for visualization of the results.

      9140 hitsBASEPLT9 3.7

      BASEPLT9 is a spreadsheet program written in MS-Excel for the purpose of analysis of steel column base plates.

      Recently Added Structural Analysis Software

      21 FebSFAT 1.10

      SFAT is a fatigue life analysis software for steel structures, components, as well as welded and bolted connections in bridges, cranes, offshore platforms, offshore wind structures, and other structures subjected to cyclic loading.

      24 JanABC: ArcelorMittal Beams Calculator 3.49

      ABC: ArcelorMittal Beams Calculator is a free pre-design tool for use in designing a variety of steel and composite structures such as portal frames, beam and column structures, trusses, and column-beam connections.

      17 JanBlasTDOF 0.1.3

      BlasTDOF is a free-to-use two-degree-of-freedom (TDOF) blast analysis software.

      27 DecMACS+ 3.0.2

      This software designs composite floor slabs at elevated temperatures by taking into account the enhancing effects of the membrane action in slab.

      炸金花打伙牌技巧